DESIGN AND PERFORMANCE ANALYSIS OF HORIZONTAL AXIS WIND TURBINE TAPERLESS NACA 6510 USING QBLADE SOFTWARE

Authors

  • Fanisya Dwiyani )Department of Industrial Engineering, Sekolah Tinggi Teknologi Cipasung, Jalan Cilampunghilir
  • Ahmad Zamakhsyari Sidiq Department of Industrial Engineering, Sekolah Tinggi Teknologi Cipasung, Jalan Cilampunghilir
  • Ahmad Said King Mongkut’s University of Technology Thonburi

Keywords:

Horizontal axis wind turbine, NACA 6510, QBlade, performance coefficient.

Abstract

The crisis of non-renewable energy resources has pushed the global community to overcome the dominance of fossil fuel power plants. The utilization of new renewable energy sources is a solution because it is considered to have energy sources that will continue to be renewed, including wind energy. Since ancient times, wind energy can be harvested and converted into electrical energy using wind turbines. This research was conducted to analyze the feasibility of the design performance of the horizontal axis wind turbine blade NACA airfoil 6510. The feasibility analysis of the performance can be known from the simulation results by referring to the resulting efficiency value. The analysis was carried out by studying literature to determine the characteristics of the NACA airfoil 6510 and performance simulation using Qblade software. The design is carried out using data on the average maximum wind speed in Indonesia of 12 m/s. Therefore, the results of the feasibility of wind turbine blade design performance with NACA airfoil 6510 have an efficiency of 44%.

References

Agency for the Assessment and Application of Technology, OUTLOOK ENERGI INDONESIA 2021 Perspektif Teknologi Energi Indonesia: Tenaga Surya untuk Penyediaan Energi Charging Station. 2021.

B. Dahlan, “RANCANG BANGUN BALING-BALING KINCIR ANGIN KAYU MAHONI (Swietenia Macrophylla) DAN PINUS DESIGN OF WIND TURBINE BASED ON THE NACA 4412 AND 4415 USING MAHOGANY (Swietenia macrophylla) DAN PINES WOOD (Pinus merkusii),†2016.

G. A. Widyaningsih, “Ulasan Peraturan Presiden Nomor 22 Tahun 2017 tentang Rencana Umum Enerfi Nasional,†vol. 4, no. 1, pp. 139–152, 2017.

S. Rehman, M. Mahbub Alam, L. M. Alhems, and M. Mujahid Rafique, “Horizontal AxisWind Turbine Blade Design Methodologies for Efficiency Enhancement A Review,†Energies, vol. 11, no. 3, 2018, doi: 10.3390/en11030506.

I. N. Zahra, “Dasar-Dasar Perancangan Bilah,†pp. 13–19, 2020.

Y. Kuntara, “Rancang Bangun Bilah Turbin Angin Sumbu Horizontal Skala Mikro,†2021.

S. D. Oktaviani, “Perancangan Bilah Turbin Angin Horizontal Jenis Taperless Pesisir Cirebon Menggunakan Software Qblade,†Universitas Singaperbangsa Karawang, 2021.

EMD International A/S. (2022) Wind Energy Resource of Indonesia [online]. Available : http://www.indonesia.windprospecting.com .

L. A. Dharman, “LISTRIK TENAGA ANGIN JENIS TAPER AIRFOIL NACA 4412 UNTUK SKALA MIKRO PROGRAM STUDI TEKNIK MESIN LISTRIK TENAGA ANGIN JENIS TAPER AIRFOIL NACA 4412 UNTUK SKALA MIKRO Disusun oleh : L . Aria Dharman NIM : 16040058,†2021.

Downloads

Published

2022-12-31

Issue

Vol. 10 No. 2 (2022)

Section

Articles

License

by-sa

This work is licensed under a 
Creative Commons Attribution-NonCommercial 4.0 International License